Heliformed suspension clamp

Home » Products » Overhead Line Solution » Heliformed Line Fitting » Heliformed suspension clamp

Use Description
Heliformed Suspension clamp is intended for use on aluminum based conductors, Aluminum Coated Steel Conductor and galvanized steel strands. It is designed
to reduce the static and dynamic stresses at the support point, so that the conductor or strand is protected against the effects of oscillations.
It also protects the conductor in the support against impulse and power flash-over.

Application
1. For the reduction of static stresses at conductor suspension points and to provide greater protection to conductors against the dynamic stresses of Aeolian vibration.
2. To give conductors protection against impulse and flash-over.
3. To protect conductors against abrasion, bending and compression stresses. The protection offered by heliformed suspension clamp fittings is superior to armor-clamp combinations.
4. To install line angles up to and including 30° and, through use of double units, up to 60°.
5. For proper performance and personal safety be sure
to select the proper size with preformed Armor Rods and clamps according the conductors size before application.
6. Dead ends are precision devices. To insure proper performance, they should be stored in cartons under cover and handled carefully.
7. If you have any question please contact with TANHO Electrical Equipment Co., Ltd.

Safety Considerations
1. This product is intended for a single (one-time) use and for the specified application.
2. This product is intended for use by trained craftspeople only. This product should not be used by anyone who is not familiar with and trained in the use of it.
3. When working in the area of energized lines with this product, extra care should be taken to prevent accidental electrical contact.

Feedback form

Bolt, Washer, Lock Nut: Galvanized Steel.
Strap: Galvanized Steel for conductor dia. Range 6.91-12.70mm High-Strength Aluminum Alloy for conductor dia. Range12.24-56.72mm.
Insert: An elastomer specifically formulated for resistance to ozone attack, weathering, extreme high and low temperature variations, and compression set. Aluminum alloy reinforcement is molded into the elastomer insert.
Housing: Galvanized Steel Stamping for cable dia. Range 6.91-12.70mm
High-Strength Aluminum Alloy Casting for conductor dia. range12.24-56.72mm.
Rods: Aluminum Clad Steel for ACSR diameter Range 7.72-12.23mm Aluminum Alloy for ACSR diameter
Range6.91-12.70mm.Aluminum Clad Steel for Aluminum Coated Steel Conductor diameter Range 6.91-12.70mm
Galvanized Steel for Galvanized Steel Conductor diameter Range 6.91-12.70mm Standard Armor Rods have dimensions which are different from Rods for suspension clamp and cannot be substituted.

For ACSR conductorDouble suspension clamp for ASCR& AAC

FOR AAC conductor                                              The Design Modifications of single suspension clamp or double suspension clamp

For line angles between 30° and 60°, use the double support arrangement with the insulator strings connected directly to the heliformed Suspension clamp.

Double Heliformed Suspension clamp

Shown below is the heliformed Suspension clamp:
Single as used for line angles between 0°and 30°.
Shown below is the heliformed Suspension clamp: Double as used for line angles between 30°and 60°.

The different connect type with various fitting:

Feedback Form
Other Products
  • Hydraulic Crimping ToolCu 70mm2, Al 50mm2 Terminal or below them can be connected fast.
    Split design with convenient use.
    There is a safe protective...
  • Connector Parallel groove clamps are mainly used for transmitting current between the interconnected conductors, for example tapping off bus-bars to equipment on substations...
  • Suspension Clamp Suspension clamps are used to connect the conductors to the insulators. The product range comprises products for all purposes. Some of the types have heli-formed rods ...
  • Tension Clamp These requirements do not apply to clamps which are used in switching substations.The components which transmit the compr essive force must be designed so that no...